• Certified verification of Remote Sensing Device (some may call it "calibration")
• Carried out in accordance to the IEC 61400-50-1 and IEC 61400-50-2, accredited as per ISO 17025
• Conducted at a 200m reference mast
• Procedure warrants lowest uncertainties, highest accuracy, and compliance in line with IEC, FGW and IEA

• 4.3151.10.001​
• TMR-Sensor (Tunnel Magneto Resistance)
• Measurement range: 0...360°
• Digital output protocoll: 16 bit serial synchronous
• Digital output: 10 bit Gray Code
• Without north gap 
• Accuracy: 0.75°
• Resolution: 0.35°
• W/o heating

• ​Ammonit Meteo-42M
• With new firmware version offering flexibility in the user setttings, sensor and modem configuration, data security, among others
• 8x analog voltage IN (± 0.1V, ± 1V, ± 10V 16bit)
• 8x pulse counter IN
• 4x digital serial status IN
• 1 RS485 Client IN (for up to 8 smart sensors or Ultra Sonic Anemometers)
• 4x analog voltage OUT (5V | Switches)
• 1x analog current OUT 
• 1 RS485 Server OUT (SCADA monitoring software)
• 3 USB (2x USB-A host, 1x USB-B device)
• 1 LAN (Ethernet)

• Module for 10 Ports / RS485 2-wire / Configurable UOUT
• Stabilised and ripple-free voltage output individually configurable
• 10 individually configurable ports
• One stabilised and ripple-free output with active current limit (110 mA)
• One configurable bus-termination resistor (120 Ω) for two-wire RS485 bus setup (half duplex)
• Each terminal comprises overvoltage protection

• ISO 9060: Secondary Standard
• Heating, tilt sensor, internal ventilation
• No external ventilator required and mitigates dew and frost
• Measurement range: -400 to 4000 W/m²
• Spectral range: 285 to 3000 nm
• Incl. calibration sheet (traceable to WRR)
• Power consumption (dew and frost mitigation mode): < 3 W

ZX 300 LIDAR - Rental Service
• Measures up to 10 customizable heights up to 300m above ground level
• Wind speed accuracy: 0.1 m/s
• Wind speed range: <1m/s to 80 m/s
• Wind direction accuracy: <0,5°
• ZX Complex Flow Solver
• 50 Hz sampling rate
• 5 years warranty included / 5 years maintenance interval

• Temperature:
    Range: -40 ... 80 °C
    Accuracy: ±0.1 °C
• Humidity:
    Range: 0 ... 100% rH
    Accuracy: ±1% rH
• Pressure:
    Range: 400 ... 1200 hPa
    Accuracy (400 ... 1100 hPa, –40 ... 85 °C): ±0.9 hPa
• Linearity Compensation: 32 points
• Interfaces: RS-485, SDI-12, USB
• IP 65
• Input Voltage: 5 ... 45 VDC

• 4.3352.10.400 - unheated
• Class A compliant according to IEC 61400-12-1 & 61400-12-1 Ed.2
• W/o heating
• Measurement Range: 0.3...75 m/s
• Outputs: RS485 / ASCII / MODBUS
• Option for connecting a bus-compatible wind vanes and anemometers in parallel (daisy chain)
• Measures next to wind speed also:
   Air pressure: 300 ... 1100 hPa (Accuracy: ±1 hPa @ 20 °C)
   Indication: Measuring range: -89.9 ... +89.9° (Accuracy: ±1 °)
   Vibration: Measuring range: 0 ... 50 Hz (Accuracy: ±0.4 Hz)
   Acceleration: Measuring range: ±8 g (Accuracy: ±30 mg)

For Thies and Vector Instruments (Windspeed Ltd.) wind vanes:For Thies and Vector Instruments (Windspeed Ltd.) anemometer:
• Certified Maintenance (OEM TIER3 authorization)
• Certified refurbishment (OEM TIER3 authorization)
• Exchange of bearings, O-rings, sealings 
• Sensor Specific Report Certificate 
• Authorisation seal

• 12V, 50 Ah
• Maintenance free, Non-spillable
• Including safety data sheet for aviation transport
• Low self-discharge ratio
• Special deep cycle battery designed for intensive cyclic discharge usage

• 8x pulse counters IN
• 3x analog voltage IN
• Requires external 12VDC power supply
• 3x configurable 'Flex' Channels (Analog or Counter) with optional signal conditioning modules (P-SCMs)
• Resolution: 16 bit ad
• Accuracy: 0.04 % of full scale
• LCD with 16 button keypad

Campbell Scientific CS211
• Low-power, smart sensor designed to monitor temperature, humidity levels and door openings inside enclosures
• The CS211 uses an optical sensor and the LED to detect if the enclosure door is open or closed
• Temperature:
    • Measurement range: –40 … +60 °C
    • Accuracy: ±0.4 °C
• Relative humidity:
    • Measurement range: 0 … 100 % RH
    • Accuracy: ± 3 % RH (10 … 90 % RH at 25 °C)
• Supply voltage: 7 to 28 VDC
• Average current consumption: <  100 µA
• Start up time: 3 s
• SDI-12 direct sonnection to a Campbell Scientific data logger
• Dimensions: 80 x 59 x 15 mm

• M83575
• 3 Ports: Pull-Up 5.1kOhm, Compact Vane
• 3 Ports: First Class Vane etc., 10mA
• 2 Ports: Pull-Down 10kOhm
• 2 Ports: Configurable, open
• RS485: Resistors for Biasing and Termination
• Output: 5V/100mA
• Supply: 9 to 32VDC

• WAV151
• Measurement range: 0 ... 360°
• Operating power supply: Uin = 9.5 ... 15.5 VDC, 20 mA typical
• Heating power supply: 20 V DC / AC, 10W, 500 mA nominal

• Once powered up, the measurement automatically starts
• Calibration certificate (standards traceable to U.K.A.S accreditation service) optionally available
• 6x analog single-ended or 3 differential IN, 2x digital pulse counters IN, 4x digital IN/OUT, 3x analog voltage OUT, 1x switched 12V OUT
• RS232, CS I/O PORT, optionally: USB, Ethernet (LAN), WiFi and CF-card modules available
• 2/4 Mbytes SRAM memory (optionally extendable)
• Surge protection for all Inputs by gas discharge tube (GDT)