Herzlich Willkommen in ProfEC's One Stop Wind Shop!

• 3.1157.10.000
• 0...5V output, set 800...1060 hPa
• 300...1100 hPa scalable
• Long-term stability ±0.3 hPa/year
• Accuracy ±1.0 hPa (unheated)
• Accuracy ±0.25 hPa (heated)

• Certified verification of Remote Sensing Device (some may call it "calibration")
• Carried out in accordance to the IEC 61400-50-1 and IEC 61400-50-2, accredited as per ISO 17025
• Conducted at a 200m reference mast
• Procedure warrants lowest uncertainties, highest accuracy, and compliance in line with IEC, FGW and IEA

WindCube Winter Kit
• Leosphere accessory for WindCube v2.1
• Tilted surface for low snow retention
• Active heating element with 2 selectable power modes (90 or 120W)
• Easy installation
• Tested in harsh weather conditions with snow and ice at -20°C
• Suitable for remote and hard-to-reach places
• Input power supply: 24.5 - 27 VDC

For Thies and Vector Instruments (Windspeed Ltd.) anemometer:
• Repair (costs are sensor specific and depend on malfunction found)
• Certificate
• Authorization seal
Scope & costs for repair depend on the individual sensor defects & conditions. A sensor specific offer will be made based upon inspection.

• Wind speed: 0 ... 60 m/s
• Wind direction: 0 ... 360°
• Pressure: 500 ... 1100 hPa
• Temperature: -52 ... +60 °C
• Relative Humditiy: 0 ... 100 %RH
• Operating voltage: 6 ... 24 VDC
• Communication Interface: SDI‑12, Modbus RTU, ASCII, NMEA 0183 v3.0
 

EFOY Pro 2800 (Fuel Cell with Bluetooth)
• Methanol Fuel Cell 
• M10/M28/M60 litre Methanol cartridges, optional up to 8 units with Fuel Manager
• Remote monitoring

• ISO 9060: Secondary Standard
• Heating, tilt sensor, internal ventilation
• Measurement range: -400 to 4000 W/m²
• Spectral range: 285 to 3000 nm
• Incl. calibration sheet (traceable to WRR)
• Power consumption (dew and frost mitigation mode): < 3 W

• Once powered up, the measurement automatically starts
• Calibration certificate (standards traceable to U.K.A.S accreditation service)
• 16x analogue single-ended or 8 differential Analog Inputs, 10x pulse counters, 8x digital IN/OUT (configurable), 4x analogue voltage (switched excitation mode or switched regulated voltage supply), 2x switched 12V 
• RS485/232, CS I/O PORT to CSI peripherals, USB, Ethernet (LAN) port, Wi-Fi (optional module)
• 4 Mbytes battery-backed SRAM + 72 MB flash memory, expandable to 8 GB
• Surge, Electrostatic Discharge and Lightning Protection for all critical Inputs and Outputs
• Power in 9.6V to 36VDC
• Stainless steel type-D connectors and gold plating improvements on RJ45s
• Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

Obelux LI-200-DCW-A
• 1x signal light, type Obelux LI-200-DCW-A, intensity 200 cd
• Specifications met: CAP 168 Civil Aviation Authority, London, UK February 2001, Flight obstacle (low intensity) 
• Integrated photocell, user selectable sensitivity: off (default), 400 lux, 800 lux, 1600 lux
• With ​​​fault monitoring
• Operating Voltage: 10 - 60 VDC
• Power Consumption: 10 W

• M83570
• 10 individually configurable ports: Current limit 10 mA, Pull-up resistor 5.1 kOhm with current limit 1 mA, and Pull-down resistor 10 kOhm
• 2-wire RS485: Biasing and Bus-termination terminal 
• 1x stabilized and ripple-free 5 V output with 110 mA current limit
• Supply: 9 to 32VDC

Autonomous power supply system for low & medium intension aviation signal lights ICAO Type A and/or B
• Operates independently from the power supply system of the measurement system
• 1x solar charge controller and regulator Solarix PR1010
• 1x battery 12V, ~105 Ah, maintenance free, non-spillable 
• 110Wp solar PV power incl. slope-adjustable mounting rack and mast support
• 1x shelter box ca. 500 x 500, incl. mast support

• Compliant to recommendations of FGW TR6, IEC and MEASNET
• Incl. calibration certificate
• Calibration standards traceable to U.K.A.S and/or NIST/NVLAP accreditation service (through ilac-MRA)
• Executed by a third party accredited calibration laboratory (DIN EN ISO/ISO 17025)

For Thies Ultrasonic Anemometers:
• Inspection and Checkup
• Verification of measurements and configuration
• Inspection report
• Certificate

• SOLAR1000
• Automated data acquisition system specifically designed for solar monitoring applications
• Measurements of Air temperature, Solar radiation—global horizontal (GH), Solar radiation—plane of array (POA), Surface temperature—back of panel, Wind direction, Wind speed, Precipitation, and Barometric pressure
• AC and/or Autonomous DC Power Supply

• Temperature:
    Measurement range: -40 ... 85 °C
    Accuracy (-40 … 85 °C, moved air > 2 m/s): ±0.1 °C
• Relative Humidity:
    Measurement range: 0 ... 100 % rH
    Accuracy: 1.5 % rH
• Pressure:
    Measurement range: 300 ... 1200 hPa
    Accuracy (@ -20 … 80°C @ 800...1100 hPa): ±0.25 hPa
• Supply Voltage: 15 ... 30 V DC
• Output:
    4 ... 20 mA, 3 Channels
    RS-485: Thies ASCII

• EKI-2541SI
• 1 x 100 Mbps Single-mode 1310 nm 30km SC type fiber port
• Half/Full duplex flow control
• 1 x 10/100 Mbps Ethernet port with RJ45 connector
• Redundant 12-48 VDC power input

• Vertical pipe mounting set: pipe min. diameter 40 mm, max. diameter 150 mm
• Stainless steel

• Increases the number of sensors the data logger can measure
• Allows to multiplex up to 64 sensors
• Decreases cost of cabling individual sensors
• Electrical surge protection
• Operating voltage: 9-16 VDC
• Operating temperature: -25°C to 50°C (standard), -55°C to 85°C (extended)