Herzlich Willkommen in ProfEC's One Stop Wind Shop!

WindCube Winter Kit
• Leosphere accessory for WindCube v2.1
• Tilted surface for low snow retention
• Active heating element with 2 selectable power modes (90 or 120W)
• Easy installation
• Tested in harsh weather conditions with snow and ice at -20°C
• Suitable for remote and hard-to-reach places
• Input power supply: 24.5 - 27 VDC

For Thies and Vector Instruments (Windspeed Ltd.) anemometer:
• Repair (costs are sensor specific and depend on malfunction found)
• Certificate
• Authorization seal
Scope & costs for repair depend on the individual sensor defects & conditions. A sensor specific offer will be made based upon inspection.

• Temperature:
    Range: -40 ... 80 °C
    Accuracy: ±0.1 °C
• Humidity:
    Range: 0 ... 100% rH
    Accuracy: ±1% rH
• Pressure:
    Range: 400 ... 1200 hPa
    Accuracy (400 ... 1100 hPa, –40 ... 85 °C): ±0.9 hPa
• Linearity Compensation: 32 points
• Interfaces: RS-485, SDI-12, USB
• IP 65
• Input Voltage: 5 ... 45 VDC

• 3.1157.10.000
• 0...5V output, set 800...1060 hPa
• 300...1100 hPa scalable
• Long-term stability ±0.3 hPa/year
• Accuracy ±1.0 hPa (unheated)
• Accuracy ±0.25 hPa (heated)

• ISO 9060: Secondary Standard
• Heating, tilt sensor, internal ventilation
• Measurement range: -400 to 4000 W/m²
• Spectral range: 285 to 3000 nm
• Incl. calibration sheet (traceable to WRR)
• Power consumption (dew and frost mitigation mode): < 3 W

• 4.3151.10.001​
• TMR-Sensor (Tunnel Magneto Resistance)
• Measurement range: 0...360°
• Digital output protocoll: 16 bit serial synchronous
• Digital output: 10 bit Gray Code
• Without north gap 
• Accuracy: 0.75°
• Resolution: 0.35°
• W/o heating

• Once powered up, the measurement automatically starts
• Calibration certificate (standards traceable to U.K.A.S accreditation service)
• 16x analogue single-ended or 8 differential Analog Inputs, 10x pulse counters, 8x digital IN/OUT (configurable), 4x analogue voltage (switched excitation mode or switched regulated voltage supply), 2x switched 12V 
• RS485/232, CS I/O PORT to CSI peripherals, USB, Ethernet (LAN) port, Wi-Fi (optional module)
• 4 Mbytes battery-backed SRAM + 72 MB flash memory, expandable to 8 GB
• Surge, Electrostatic Discharge and Lightning Protection for all critical Inputs and Outputs
• Power in 9.6V to 36VDC
• Stainless steel type-D connectors and gold plating improvements on RJ45s
• Standard operating range of -40° to +70°C (optionally extended: -55° to +85°C)

For Thies and Vector Instruments (Windspeed Ltd.) wind vanes:For Thies and Vector Instruments (Windspeed Ltd.) anemometer:
• Certified Maintenance (OEM TIER3 authorization)
• Certified refurbishment (OEM TIER3 authorization)
• Exchange of bearings, O-rings, sealings 
• Sensor Specific Report Certificate 
• Authorisation seal

ZX 300 LIDAR - Rental Service
• Measures up to 10 customizable heights up to 300m above ground level
• Wind speed accuracy: 0.1 m/s
• Wind speed range: <1m/s to 80 m/s
• Wind direction accuracy: <0,5°
• ZX Complex Flow Solver
• 50 Hz sampling rate
• 5 years warranty included / 5 years maintenance interval

• Certified verification of Remote Sensing Device (some may call it "calibration")
• Carried out in accordance to the IEC 61400-50-1 and IEC 61400-50-2, accredited as per ISO 17025
• Conducted at a 200m reference mast
• Procedure warrants lowest uncertainties, highest accuracy, and compliance in line with IEC, FGW and IEA

• Temperature:
    Measurement range: -40 ... 85 °C
    Accuracy (-40 … 85 °C, moved air > 2 m/s): ±0.1 °C
• Relative Humidity:
    Measurement range: 0 ... 100 % rH
    Accuracy: 1.5 % rH
• Pressure:
    Measurement range: 300 ... 1200 hPa
    Accuracy (@ -20 … 80°C @ 800...1100 hPa): ±0.25 hPa
• Supply Voltage: 15 ... 30 V DC
• Output:
    0 ... 10 V, 3 Channels
    RS-485: Thies ASCII

• ISO conform calibration by accredited Calibration Laboratory
• Compliant to recommendations of FGW TR6, ISO / IEC and MEASNET
• Incl. calibration certificate
• Fully traceable to national standard

• ISO 9060: Secondary Standard
• Measurement range: 0 W/m² to 4000 W/m²
• Spectral range: 285 to 3000 nm
• Incl. calibration sheet (traceable to WRR)
• For Global Horizontal Irradiance (GHI) measurements (W/m2) 
• Sunshine duration (optional)
• With 10 kOhm thermistor
• With heating

​• Solarzelle: Monokristallines Silizium (50 mm x 33 mm)
• Protokoll: M&T (Typ -MT), MODBUS RTU (Typ -MB)
• Typische Messungenauigkeit : ±0.4 W/qm ± 1.6%
• Ausgangssignal: 0 - 10V für 0 - 1.500W/m²
• Arbeitstemperatur: -35°C bis 80°C

• Starlink Standard Kit V4
• Frequency: 2,4 GHz / 5 GHz
• IEEE 802.11 a/ac/ax/b/g/n
• 2 x LAN ports 10/100/1000 Mbps
• Antenna power consumption: Average: 75–100 W
• Antenna (LxWxH) 594 x 383 x 40 mm
• Router (LxWxH) 299 x 43 x 120 mm
• Intended for a fixed installation

• 3.1157.10.140
• 0...20mA output, set 800...1060 hPa
• 300...1100 hPa scalable
• Long-term stability ±0.3 hPa/year
• Accuracy ±1.0 hPa (unheated)
• Accuracy ±0.25 hPa (heated)

• WAV151
• Measurement range: 0 ... 360°
• Operating power supply: Uin = 9.5 ... 15.5 VDC, 20 mA typical
• Heating power supply: 20 V DC / AC, 10W, 500 mA nominal

• Pressure: 300 … 1200 hPa
• Temperature: –50 … 60°C
• Relative Humditiy: 0 … 100 %RH
• Operating power consumption: 4 … 32 V
• Digital output: RS485, 2-wire, half-duplex
• Communication protocoll: UMB-Binary, UMB-ASCII, SDI-12, MODBUS
• Protection type housing: IP66

​• Plastic Enclosure
• Complete internal wiring, clamps, etc. ready for plug&play
• Includes terminal connectors and internal wiring to connect sensors, modem, data logger, charge controller and power supply
• Incl. mounting of other, ordered equipment from One Stop Wind Shop like barometer, modem, data logger, charge controller, battery, etc.
• Individual ground / earthing conductor lug for sensor mounting plate and shields (needed for galvanic separation of measurement system and cabinet from mast structure)